D-Link DGS-3700 User Manual Page 39
- Page / 177
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DAS-3626 VDSL2 Switch User Manual
DHCP Relay Interface Settings
This window allows the user to set up a server, by IP address, for relaying DHCP information to the switch. The user
may enter a previously configured IP interface on the switch that will be connected directly to the DHCP/BOOTP
server using the following window. Properly configured settings will be displayed in the DHCP Relay Interface Table
at the bottom of the following window. The user may add up to four server IP’s per IP interface on the switch.
To view this window, click System Configuration > DHCP/BOOTP Relay > DHCP/BOOTP Relay Interface Settings
as shown below:
Figure 42. DHCP/BOOTP Relay Interface Settings and DHCP/BOOTP Relay Interface Table menu
The following parameters may be configured or viewed:
Parameter Description
Interface The IP interface on the switch that will be connected directly to the Server.
Server IP Enter the IP address of the DHCP server. Up to four server IPs can be configured per IP
Interface.
Click Apply to implement changes made.
39
- User Manual 1
- Table of Contents 3
- Intended Readers 5
- Notes, Notices, and Cautions 5
- Section 1 6
- Introduction 6
- Login to Web Manager 8
- Web-based User Interface 9
- System Save Menus 10
- System Tools Menus 11
- Upload Log File 11
- Download Firmware 12
- Reboot System 12
- System Configuration 14
- System Information 15
- Interface Settings 15
- IPv6 Neighbor Settings 17
- Serial Port Setting 18
- Web Settings 18
- Telnet Settings 18
- System Time and SNTP Settings 19
- Time Zone Settings 20
- User Account Settings 22
- System Log Configuration 24
- Switch Configuration 26
- MAC Address Aging Time 27
- Ethernet Settings 27
- Traffic Segmentation 29
- Port Mirror 30
- Port Trunking 31
- LACP Port Settings 32
- Loopback Detection Settings 33
- Q-in-Q Settings 34
- GVRP Global Settings 35
- GVRP Settings 35
- DHCP Relay 37
- DHCP Relay Interface Settings 39
- Spanning Tree 40
- STP Bridge Global Settings 41
- STP Port Settings 43
- STP Instance Settings 45
- MSTP Port Information 46
- CFM Global Settings 48
- CFM MD Settings 49
- CFM MA Settings 49
- CFM Mep Settings 50
- CFM Remote Mep 50
- CFM Loopback Settings 51
- CFM Linktrace Settings 51
- VDSL Configuration 53
- VDSL Ports 56
- VDSL Ports Config 57
- VDSL Loopback 57
- Multicasting 59
- IGMP Snooping Settings 60
- MLD Snooping 66
- MLD Snooping Settings 67
- Multicast Forwarding 72
- Multicast Filtering Mode 73
- Storm Control 74
- Section 7 76
- Advantages of QoS 77
- Understanding QoS 77
- Bandwidth Control 78
- 802.1p Default Priority 79
- 802.1p User Priority 79
- QoS Scheduling Mechanism 80
- QoS Scheduling 80
- In Band Manage Settings 82
- 802.1p Map Settings 83
- Section 8 84
- ACL Configuration Wizard 84
- Access Profile List 85
- ACL Finder 102
- Section 9 103
- Management VLAN 103
- 802.1v Protocol VLAN 107
- Security 109
- Safeguard Engine 110
- Trusted Host 111
- Port Security 112
- Access Authentication Control 113
- Authentication Server Group 115
- Authentication Server 116
- Login Method Lists 117
- Enable Method Lists 118
- RADIUS Accounting Settings 121
- CPE Management 122
- CPE Basic Information 123
- CPE Advanced Information 124
- CPE WAN Settings 125
- CPE PPPoE Settings 126
- CPE LAN Settings 127
- CPE Server Status 127
- CPE VLAN Settings 128
- CPE ProtoVLAN Settings 129
- CPE QoS Settings 130
- CPE Filter 131
- CPE SNMP 133
- CPE Firmware 133
- CPE Loopback 134
- CPE Maintenance 134
- Section 12 135
- VDSL Status 135
- 1 Day ES/SES/UAS 136
- VDSL PM Threshold 136
- CPU Utilization 137
- Port Utilization 138
- Packet Ports 139
- Received (RX) 141
- UMB_cast (RX) 143
- Transmitted (TX) 145
- Error Ports 147
- Utilization 151
- Ping Test 152
- Firmware Information 153
- Maintenance 154
- SNMP Settings 155
- SNMP Global State Settings 156
- SNMP View Table 156
- SNMP Group Table 157
- SNMP User Table 158
- SNMP Community Table 159
- SNMP Host Table 160
- SNMP v6Host Table 160
- SNMP Engine ID 161
- SNMP Trap Configuration 162
- System Log Entries 163
- DAS-3626 Trap List 172
- Proprietary Trap List 172
- Glossary 174
- Password Recovery Procedure 176
- Command Parameters 177
Related products and manuals for Network switches D-Link DGS-3700
(3 pages)
Network switches D-Link DGS-3212SR User Manual
(144 pages)
(144 pages)
Network switches D-Link DGS-3024 Specifications
(186 pages)
(186 pages)
Network switches D-Link DKVM-4 - KVM Keyboard Video Mouse Switch Hotkey/Autoscan User's Guide
(39 pages)
(39 pages)
Network switches D-Link DES-3052 Specifications
(271 pages)
(271 pages)
Network switches D-Link DES-7100 User Manual
(111 pages)
(111 pages)
© 2020, manymanuals.com. All rights reserved. | 0.447 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals