D-Link DVG-2032S User Manual

1 DVG-2032S VOIP Gateway User Manual Version 1.

Telephone Interface Description Example for DVG-2032S: DVG-2032S connecting directly to phone sets After connecting telephone sets to P1-P32, use

7 3. Setting the Gateway through IVR VoIP transmits voic

Instructions  FXS Port: Connected to telephones. To enter IVR mode, enter “ * * password #” after hearing the dial tone. When you hear a seco

9 IVR Functions Table: Function Code Description Exam

Function Code Description Example 215/205 Set/Query Gateway Telephone Number (Representative Number) 216/206 Set/Query the extension number of

11 IP Configuration Settings—Setting IP Configuration of

PPPoE Account Settings  After entering IVR mode, dial 121.  After hearing “Enter value”, enter the account number, followed by ”#”. Example:

13 PPPoE Character Conversion Table Number Input Key U

1. Setting a Gateway with WEB Browser The gateway allows users to make settings using a web browser. After opening a browser, enter Gateway’s IP add

15  Listen Port UDP: It is not necessary to change t

and Line 2 is using 9002 and 9003, and so forth. IP Configuration (Setting WAN Port) There are four methods of obtaining a WAN port IP address:

17 Select “PPTP” and enter the IP Address, Subnet mask

Some Internet Service Providers (ISP) assigns the bandwidth via the MAC (Media Access Control) Address. You can click the " Clone" butto

19 Network Settings (LAN) LAN interface mode※  Ro

QoS Settings WAN QoS  QoS (Quality of Service): Sets an external bandwidth to ensure sound quality during transmission (When this function is ena

21 NAT/DDNS NAT Traversal If a Gateway is set up un

DDNS These settings are only necessary when the gateway is set up under a NAT that uses a dynamic IP address and do not support DDNS.

23 Choose a DDNS Server: The current system allows users

 Enable: Enable a line; if some lines are not used, disable them (Pause Function) to avoid unnecessary waiting when an incoming call is diverting

25  Hunting/Ring: It is able to set FXS group hunting

Contents 1. Introduction...1 Product Overview...

 SIP Message Resend Timer Base: SIP packet will resend if response didn't arrive in the base time set in this column. It will send again at

27  Enable Support of SIP Proxy Server / Soft Switc

 Initial Unregister: After rebooting, it is unregistered first and then do the general registry process.  Enable Message Waiting Indication: The

29 Calling Features  Do Not Disturb: It will only be

Calling Feature Instructions:  Call Hold: Ongoing call will be put on hold after FLASH button pressed on the phone set. The gateway will play a r

31 Advanced Options  There are two levels to enter

 Enable Out-of-Band DTMF: To send DTMF keys (0~9, *, #,) follow the RFC2833 rules or via SIP Info.  Enable Hook Flash Event: The gateway will de

33 the sound quality and occupied bandwidths are also di

 Drop Silent Call Timeout: Set the time to hang up the phone.

35 Digit Map There are 50 sets of leading digit entries

2 3. Coding Principle...46 Instruction...

Method 1- Single mapping: Fill a short code into the “Speed Dial Code” column, and enter the desired phone number into the “Number To Dial” column

37 CDR Settings The user can set up a CDR Server to reco

System Information This page shows that the status of VoIP Gateway. There are Port Status, Server Registration Status, WAN Port Information, LAN Por

39 RTP Packet Summary Displays the information of the la

SNMP  Enable SNMP Agent: Enable SNMP if ticked.  Get/Set/Trap Community: Enter Community name to Read, Write and Trap.  Trap Host: Enter the

41 Provision Settings Fill in the parameters needed of

Software Upgrade Gateway provides software upgrade function for a remote end. Your provider gives all parameters.  Upgrade Server: Choose the

43 2. IP Sharing Functions All Gateway series have a bui

The IP settings on PC are as follows (using Windows 2000 for example) Open Start->Settings->Control Panel Open Network and Dial-up Connectio

45 Select “Use the following IP Address ” and enter I

1 1. Introduction Product Overview The stand-alone VoIP

3. Coding Principle Instruction  After a phone number is entered, dial # to call out immediately or, wait until the “Inter DTMF Timeout” expires

47 StartEnter a phone number (D#)Is (D#) defined in S

2 Product Features ● SIP (RFC 3261) compliant ● Optional server enables small businesses to build up private VoIP network (SIP model) ● QoS support

3 Hardware Description Front Panel  Power Indicato

2. Installation and Applications Network Interface The network interface is divided into 3 basic modes as described below:  Gateway can be ass

5 Gateway in a NAT network The gateway uses a virtual I